Guide
How to set up a new Japanese chisel: the hollow back and the steel hoop
Japanese chisels (鑿, nomi) arrive almost ready, but not quite. The maker expects you to do two things yourself: polish the back, and set the hoop on the handle. Neither is difficult, and both make a big difference to how the chisel performs and lasts.
The back is hollow. Did I get a defective chisel?
There's a shallow scoop ground into the flat back of the chisel, and you're not sure whether to flatten it out.
Why it happens
- That hollow is the ura, and it's intentional. It makes the back quicker to flatten, because you only need to polish a narrow land around the edges.
How to fix it
- Don't grind the hollow away. Flatten and polish only the lands: the strip along the cutting edge and the two sides.
- Work the back on a flat medium stone (around 1000 grit), then a finish stone, until the land along the cutting edge is bright and even all the way across.
- Keep the pressure close to the cutting edge, with your fingers on the back right behind the edge.
Prevent it: After years of sharpening, the land at the cutting edge eventually disappears into the hollow. Fixing that (ura-dashi, tapping out the back) is an advanced job. Most hobbyists will not need it for years.
The steel hoop on the handle is loose or falls off
The metal ring (katsura) at the top of the handle wobbles, or the end of the handle starts to split when you strike it.
Why it happens
- Japanese chisels are sold with the hoop sitting high on purpose. You're expected to set it yourself, so it fits the handle snugly.
How to fix it
- Take the hoop off. Soften the end fibers of the handle slightly by tapping around the edge with a hammer, or by pressing them in a vise with padded jaws.
- Tap the hoop back on until about 1 to 2 mm of wood stands above it.
- Strike the end of the handle gently with a hammer, working around the edge, so the wood mushrooms over the hoop. That locks it in place.
Prevent it: If the hoop loosens again in a dry season, tap it down a little more and mushroom the end again. It's normal maintenance.
The edge chips or crumbles
Tiny chips appear in the edge, especially in hardwood.
Why it happens
- Japanese chisels are usually very hard (often in the low 60s on the Rockwell C scale). They take a keen edge, but a thin bevel is fragile.
- Using the chisel as a lever to pry out waste.
- On a new chisel, the factory edge often hasn't been properly sharpened yet.
How to fix it
- Sharpen past the chips on a coarse stone, then go up through your finer stones.
- For hardwood, increase the bevel to around 30 degrees, or add a small secondary bevel (a few degrees steeper) at the very edge.
- Remove waste by chopping and paring instead of levering.
Prevent it: It's common for a new chisel to chip less once it has been sharpened a few times. Don't judge the steel by its first edge.
Rust spots on the blade
Orange spots appear after a few days, especially on the back.
Why it happens
- Japanese tool steels are usually high-carbon and not stainless. Moisture from water stones, sweat and humid air all cause rust.
How to fix it
- Remove light rust with a fine stone or fine abrasive paper, working flat on the back.
- Dry the tool completely after sharpening, then wipe on a thin film of oil. Camellia oil (tsubaki abura) is the traditional choice.
Prevent it: Keep a rag with a few drops of oil in a small container at the bench, and wipe each tool before you put it away.
Not sure what to strike your chisel with? A steel hammer (genno) is what hooped chisels are designed for, though a mallet works too.
Want all 20 fixes in one printable guide?
The Japanese Hand Tool Fix-It Guide has every problem with step-by-step fixes, prevention tips, clear diagrams, a sharpening routine and a glossary of Japanese terms. 20 pages, PDF.
See the guide ($14)