Guide
Which side of a ryoba do you use? Rip vs crosscut teeth explained
A ryoba (両刃, double-edged saw) is often the first Japanese saw people buy, and the first question is always the same: which edge do I use? The answer depends on the direction of the grain. Once you've got that right, most of the remaining problems come from pushing the saw.
Which side of the ryoba do I use?
A ryoba has teeth on both edges and they look almost the same.
Why it happens
- The two edges are made for different jobs. Using the wrong side is slow, rough, and puts more stress on the teeth.
How to fix it
- Rip side (along the grain): larger teeth, filed straight across like small chisels. They lift long shavings.
- Crosscut side (across the grain): smaller teeth with a pointed, knife-like bevel. They slice the fibers.
- Diagonal cuts and plywood: use the crosscut side.
- On many ryoba the teeth get finer toward the handle end. Use those finer teeth to start a cut.
Prevent it: Put a dab of paint on the handle on the rip side so you can tell at a glance.
The cut is hard to start
The saw skips across the surface, scratches the board, or jumps off the line.
Why it happens
- Starting with the saw too steep.
- Starting in the middle of the edge instead of at a corner.
How to fix it
- Start at the far corner with the saw nearly flat (about 10 to 15 degrees) and make a few short, light pulls to make a notch. Then raise the angle.
- Rest the side of your thumb's knuckle against the blade as a guide for the first strokes. Keep your thumb above the teeth.
- Use a square block clamped to the line as a fence for the first few strokes.
Prevent it: Knife a line and chisel a small V-notch on the waste side. It's the most reliable way to start exactly on the line.
The cut wanders off the line
You start on the line, but a few strokes later the kerf drifts left or right and you can't steer it back.
Why it happens
- Pushing down or forcing the stroke. Japanese saws cut on the pull; extra pressure flexes the thin blade and it follows the path of least resistance.
- A white-knuckle grip twists the blade a few degrees with every stroke.
- Short, choppy strokes that use only a few teeth.
- Watching only one face of the board, so the saw drifts out of square on the face you can't see.
How to fix it
- Back up a few strokes and re-establish the kerf with light, slow pulls. A thin blade will follow a corrected kerf if you don't fight it.
- Hold the handle near the end with a relaxed grip, thumb and forefinger doing most of the work. Let the weight of the saw do the cutting.
- Use long strokes that run most of the length of the blade.
- Mark the line on two faces (the top and the face toward you) and keep both in view.
Prevent it: Score the line first with a marking knife and pare a small V-groove on the waste side with a chisel. The saw drops into the groove and starts straight.
The saw binds or sticks in the cut
The blade gets harder to pull halfway through the board, or jams completely.
Why it happens
- The kerf is closing behind the saw. This happens a lot when ripping, as stresses in the wood are released.
- You are pushing on the return stroke. A pull-saw blade is thin and buckles under push pressure.
- Using the crosscut teeth to rip along the grain (or the reverse), which clogs and slows the cut.
- Resin or wet wood packing the teeth.
How to fix it
- Tap a thin wedge or a shim into the kerf behind the saw to hold it open.
- Make the return stroke a light, passive glide. All the work happens on the pull.
- Check which side of a ryoba you are using (see the diagram). Rip with the larger teeth, crosscut with the smaller teeth.
- Clean the teeth with a brush and a little mineral spirits, then wipe on a thin coat of oil.
Prevent it: Support both sides of the cut so the offcut doesn't sag and pinch the blade near the end of the cut.
If teeth have already chipped, or the blade has a kink, see the troubleshooter. On a replaceable-blade saw, a new blade is usually the cheapest fix.
Want all 20 fixes in one printable guide?
The Japanese Hand Tool Fix-It Guide has every problem with step-by-step fixes, prevention tips, clear diagrams, a sharpening routine and a glossary of Japanese terms. 20 pages, PDF.
See the guide ($14)