Guide
How to adjust a kanna blade with a hammer (advance, retract, level)
A kanna (鉋) has no knobs and no screws. You set the blade with light hammer taps. It feels like guesswork at first, but there are only three moves to learn, and the plane will tell you, through the shavings, whether you got them right.
How do I adjust the blade? It feels like guesswork
There are no knobs or screws, only a block of wood and a hammer.
Why it happens
- Japanese planes are adjusted with light hammer taps. That's the design, not a missing part.
How to fix it
- To advance the blade (deeper cut): tap the top of the blade (the head), gently.
- To retract the blade (shallower cut): tap the top edge of the end of the body that the blade leans toward (the daigashira). Tap the two corners alternately so the blade comes back straight. The shock loosens the blade.
- To even out a cut that's thicker on one side: tap the side of the blade near the top, toward the side that cuts thin.
- Sight down the sole toward a light. You should see a thin, even line of steel. Make small taps and check again after each one.
Prevent it: After retracting, tap the chipbreaker too, so it stays tight against the blade.
The blade is too tight, or too loose, in the body
You need heavy blows to move the blade, or it slides out with a light tap and won't stay put.
Why it happens
- The blade is held only by wedge action in the side grooves (osae-mizo). New blades are often fitted tight on purpose.
- Wood shrinks and swells with humidity, so the fit changes from season to season.
How to fix it
- Too tight: rub pencil lead on the blade, insert it, and tap it out. Shiny or dark spots show where it binds. Pare those spots in the grooves very lightly with a chisel and try again.
- Too loose: glue a strip of thin paper into the grooves, let it dry and trim it, then test again.
- The aim is for the blade to stop about 3 to 5 mm short of the sole when you push it in by hand, then reach cutting position after a few hammer taps.
Prevent it: Remove the blade when you're not using the plane for a long time, so the body doesn't stay under stress.
Chatter and tearout
The surface has ripples, or the plane rips chunks out of the wood instead of leaving a smooth finish.
Why it happens
- The chipbreaker (uragane) isn't seated tightly against the blade, so the blade vibrates.
- The chipbreaker edge is too far back from the cutting edge to break the shaving.
- Planing against the grain.
How to fix it
- The chipbreaker should touch the blade right along its edge. Check by holding them together toward a light. If you see a gap, bend the two 'ears' at the ends of the chipbreaker slightly so it presses harder.
- For difficult grain, set the edge of the chipbreaker very close behind the cutting edge (a few tenths of a millimetre).
- Read the grain on the edge of the board and plane downhill. If the tearout gets worse, turn the board around.
- Take a thinner shaving. Retract the blade a little.
Prevent it: The pressure points on the chipbreaker are the corners at the cutting end. Bend the ears in small steps; overbending makes it hard to insert.
The sole isn't true
The plane cuts only at one end of a board, takes uneven shavings, or rocks on a flat surface.
Why it happens
- The dai is wood. It moves with the seasons and needs re-truing now and then, just like a stone needs flattening.
- A Japanese smoothing plane isn't meant to be dead flat along its whole length. It's meant to touch at a few specific points.
How to fix it
- Set the blade in its working position, then retract it slightly. Always true the sole with the blade under tension, because the wedging changes the shape.
- For a smoothing plane, the sole should touch at the front edge, just ahead of the mouth, and at the rear edge. Relieve the areas in between by a hair.
- Check with a straightedge toward a light. Scrape the high areas with a sole-scraping plane (dai-naoshi kanna) or a scraper, a little at a time.
- Check again on a flat surface with a sheet of paper. The paper should be gripped at the contact points and slide freely elsewhere.
Prevent it: Recheck the sole whenever the season changes or the plane has been stored somewhere with different humidity.
If your plane won't take a shaving at all, start with sharpening, then blade fit, then the sole, in that order.
Want all 20 fixes in one printable guide?
The Japanese Hand Tool Fix-It Guide has every problem with step-by-step fixes, prevention tips, clear diagrams, a sharpening routine and a glossary of Japanese terms. 20 pages, PDF.
See the guide ($14)